Terms for subject Metallurgy containing range

English	Chinese
age hardening range	时效硬化温度范围
ageing range	时效温度范围
allowable crown control range	凸度允许控制范围
allowable crown control range	【压】 允许凸度控制范围
alpha range	α粒子的射程
alpha range	α 相区
annealing temperature range	退火温度范围
austenitic range	奥氏体范围
austenitic range	奥氏体区
austenitic temperature range	奥氏体温度范围
beta range	β 相区
black heat range	可见光起点温度范围 (~525°C)
blue brittle range	蓝脆范围
blue heat range	蓝脆性温度范围
bright plating range	光亮电镀电流密度范围
capacity range	电容范围
capacity range	容量范围
capacity range	能力范围
capacity range	负载范围
carbide precipitation range	碳化物沉淀范围
carbide precipitation range	碳化物沉淀区
cast speed range	拉速范围
casting speed range	拉坯速度范围
casting speed range	拉速范围
close-range interaction	近程相互作用
close-to-critical range	亚临界区范围
close-to-critical range	下临界区范围
composition range	成分范围
composition range of powder	保护渣成分范围
concentration range	浓度范围
critical range	临界区域
critical range	临界范围
critical temperature range	临界温度范围
crown control range	凸度控制范围
degree of long-range order	【金】 长程有序度
degree of long-range order	长程有序度
degree of short-range order	短程有序度
delta range	δ区
destruction of short-range order in alloy	合金中近程序的破坏
distillation range	蒸馏范围
effective range	刻度的工作部分
elastic range	弹性范围
elastic strain range	弹性应变范围
endurance range	持久极限
endurance range	持久范围
energy range	能量范围
energy range	能量区
exposure range	曝光范围
fatigue range	疲劳范围
ferritic range	铁素体范围
ferritic range	铁素体区
firing range	烧成范围
flow temperature range	流动温度范围
fluid temperature range	流态化温度范围
flux composition range	保护渣成分范围
forbidden energy range	能量禁区
forbidden energy range	禁能量范围
forbidden energy range	禁能量区
forbidden range	禁区
freezing range	凝固范围
fusion range	熔融范围
gamma range	γ相区
goal grain size range	目标粒度范围
hardening range	淬硬区
hardening range	淬硬范围
hardening temperature range	淬火温度区间
high-temperature range	高温范围
horizontal linearity range	水平线性偏转范围
hot short range	热脆范围
inelastic range	非弹性范围
limiting range of stress	应力极限范围
liquid range	液相范围
liquid range	液相区
load range	荷载幅度
loading range	负荷范围
loading range	载荷范围
long-range controlled continuous caster	远程控制连铸机
long-range gas	远距离运输气体
long-range interaction	长程相互作用
long-range order	长程有序
long-range order lattice	长程有序点阵
long-range order lattice	长程有序晶格 【点阵】
long-range order lattice	长程有序晶格
long-range order parameter	长程有序参数
long-range ordered alloy	长程有序合金
long-range planning	长期规划
long-range planning	远景规划
long-range radiation	长程辐射
long-range strain	长程应变
low ductility temperature range	低延性温度区间
lower range value	下限值
magnetic changes in A2 temperature range	A2 转变温度区域内的磁性变化
magnetic excursion range	磁滞回路偏移范围
martensite decomposition range	马氏体分解范围
martensite decomposition range	马氏体分解温度区
martensite range	马氏体区
medium/ fast range of casting speeds	中速和高速铸造范围
medium/ fast range of casting speeds	中速和高速铸造区
melting range	熔化温度范围
melting temperature range	熔化温度范围
mold lead range	结晶器超前量范围
nitriding range	氮化渗氮范围
nitriding range	氮化范围
nitriding range	渗氮范围
nitriding range	氮化渗氮区
normal oreing range	标准加矿温度范围
normal range	正常范围
number range	数值范围
operating range	作用距离
optimum particle-size range	最佳粒度范围
optimum range	最佳范围
optimum size range	最佳尺寸范围
optimum size range	最佳粒度范围
ore with caution range	慎加矿石的温度范围
"ore with caution" range	容许添加少量矿石的温度范围
"ore with caution" range	"小心加矿石"温度范围
oscillation frequency change range	振频变化范围
oscillation stroke adjustment range	振幅调整范围
oscillation stroke range	振幅调整范围
particle-size range	粒度范围 (Ferrosilicon is supplied in lumps or as crushed and screened particles. The particle-size ranges and tolerances shall be in accordance with table 2.硅铁以块状即经破碎并筛分的块状供货。其粒度范围与公差应符合表2的规定。)
particle-size range	粒度范围
pearlite range	珠光体区
pearlite range	珠光体范围
perfect long-range order	完全长程有序
phase transformation range	相变范围
plastic range	塑性变形范围
plastic temperature range	塑性温度范围
precipitation range	沉淀区
precipitation range	析出范围
precipitation range	析出区
precipitation range	沉淀范围
prescribed range	规定范围
preset range	预定范围
preset range	规定范围
quenching temperature range	淬火温度区间
quenching temperature range	淬火温度范围
range check	区域检査
range check	范围检査
range finder	测距仪
range of application	应用范围
range of composition	成分范围
range of lay	【压】捻距范围
range of lay	捻距范围
range of linearity	线性关系区
range of linearity	线性关系范围
range of linearity	线性区
range of measurement	测量极限
range of orientation	取向范围
range of orientations	取向范围
range of plasticity	塑性区
range of plasticity	塑性范围
range of proportionality	弹性变形区
range of proportionality	压弹性比例极限
range of proportionality	弹性变形范围
range of proportionality	比例极限
range of rhomboidity value	菱变值范围
range of sheet thickness	薄板厚度范围
range of speed	速率范围
range of speed	速度范围
range of stability	稳定范围
range of stability	稳定区域
range of variation	波动范围
range of variation	变化范围
range-percent	波动范围百分比
range resolution	范围清晰度
range resolution	距离清晰度
red heat range	红热温度范围
red heat range	赤热温度范围
reel drum with a multistage expansion range	多级胀缩的卷筒
resonance range	谐振范围
roasting temperature range	焙烧温度区间
safe range	安全范围
scale range	量程
scale range	刻度范围
short-range disorder	短程无序
short-range order	短程有序
short-range order decrease	近程序降低
short-range order lattice	短程有序点阵
short-range order lattice	短程有序晶格
short-range order parameter	短程有序参数
short-range ordered alloy	短程有序合金
short-range ordering	短程有序化
short-range repulsive force	短程斥力
short-range stress	短程应力
sieve size range	筛分粒度范围
sieve size range	筛析粒度范围
sintering range	烧结温度范围
size range	粒度上下限
size range	粒度范围
size range index	粒度范围指数
size range index	尺寸大小范围指数
slant-range condition	斜距条件
slant-range condition	斜距状况
slip-line range	滑移线范围
softening range	软化温度范围
softening range	软化范围
solid solution range	固溶范围
solid solution range	固溶体区
solidification range	凝固温度范围
strain range	应变范围 (【技】一个应变周期内最大与最小应变值的代数差。)
strain-hardening range	应变硬化范围
strain-hardening range	应变硬化区
strength range	强度范围
stress range	应力范围
stroke range	振幅调整范围
subsieve range	筛下范围
subsieve range	亚筛范围
subsieve size range	亚筛粒度范围
sweep range	扫描区
sweep range	扫描范围
target grain size range	目标粒度范围
target size range	目标粒度范围
target size range	合格粒度范围
temperature range	温度范围
tempering range	回火温度范围
tempering temperature range	回火温度范围
The slab widths produced range from 800 to 1600 mm	生产的板坯宽度范围为800 ~ 1600mm31. 5 ~63in
theory of long-range order	长程有序理论
theory of short-range order	短程有序理论
threshold stress intensity factor range	门槛应力强度因子幅度
threshold stress intensity factor range	界限应力强度因子幅度
time-bass range	时基范围
timing range	计时范围
transformation range	转变范围
transformation range	转化范围
transition range	转变范围
transition temperature range	转变温度范围
traveling range	行驶范围
travelling range	行驶范围
troostite formation range	屈氏体形成范围
troostite formation range	屈氏体形成区
turndown range	调整范围
upper range value	上域值
variation range	波动范围
welding range	焊接电流调整范围
work-hardening range	加工硬化范围
work-hardening range	加工硬化区加工硬化范围
working range	加工范围